Alpha-Gal IgE Prevalence Patterns in the United States: An Investigation of 3,000 Military Recruits.

BACKGROUND: IgE to the oligosaccharide galactose-alpha-1,3-galactose (alpha-gal) is an important cause of allergic reactions to mammalian meat. The "alpha-gal syndrome" is strongly associated with a preceding history of tick bites and in the United States is most commonly reported in parts of the southeast, but there has been limited investigation into national alpha-gal sensitization patterns and the relevance of other risk factors. OBJECTIVE: To systematically investigate alpha-gal IgE prevalence, regional patterns, and risk factors. METHODS: Alpha-gal IgE was measured by ImmunoCAP in biobanked serum samples collected from 3000 service members who presented for intake to 1 of 10 military bases in the central/eastern United States. Alpha-gal IgE sensitization (cutoff 0.1 international units/mL) was related to home of record at enlistment. RESULTS: Of the cohort, 2456 (81.9%) subjects were male, median age was 19 years (interquartile range: 18-22 years), and alpha-gal IgE was detected in 179 (6.0%). Home of record spanned all 50 states, with a median of 36 recruits per state (range: 3-261). The highest prevalence rates were in Arkansas (39%), Oklahoma (35%), and Missouri (29%), with several other southeastern states >10%. Granular mapping revealed sensitization patterns that closely mimicked county-level Amblyomma americanum reports and Ehrlichia chaffeensis infections. Sensitization was associated with male sex, rural residence, and White race in univariate and multivariable models. CONCLUSIONS: In this systematic survey, the prevalence of alpha-gal IgE among incoming military personnel was 6.0%. There were significant regional differences, with an overall pattern consistent with the known range of the lone star tick (A. americanum) and highest frequency in an area including Arkansas, Oklahoma, and Missouri.

The fit of zirconia core fabricated with CAD/CAM system / 대한치과보철학회지

STATEMENT OF PROBLEM: The use of zirconia prostheses fabricated with CAD/CAM system is on an increasing trend in dentistry. However, evaluation of the fit related to internal relief and marginal reproducibility of zirconia has not been reported. PURPOSE: This study was to evaluate the fit related to internal relief and marginal reproducibility of zirconia core fabricated with CAD/CAM system. Materials and methods: The evaluation was based on 30 zirconia cores and 5 IPS-Empress2 cores. Zirconia cores were fabricated in different conditions of internal relief(0, 10, 20, 30, 40 and 50 micrometer), and IPS-Empress2 cores were fabricated in accordance with the manufacturer's instructions. Before cementation, the marginal discrepancies of cores were measured on metal die. And then, each core was cemented to stone die, embedded in an acrylic resin and sectioned in two planes(mesiodistally and labiopalatally). The internal gaps were measured at the margin and axial surface. Measurements for the marginal discrepancies, the internal marginal gaps and the internal axial gaps were performed under a measuring microscope(Compact measuring microscope STM5; Olympus, Japan) at a magnification of *100. In addition, the marginal configurations of metal die, zirconia core and IPS-Empress2 core were examined with SEM(S-2700, Hitachi, Japan). RESULTS: Within the limits of this study the results were as follows. 1. Compared with IPS-Empress2 cores, the marginal discrepancies of zirconia cores had no significant differences, the internal marginal gaps were statistically smaller and the internal axial gaps were statistically larger in each condition of internal relief. 2. The marginal discrepancies and the internal marginal gaps of zirconia cores had no significant differences related to the conditions of internal relief(P>0.05). 3. The internal axial gaps of zirconia cores with 0.20micrometer for internal relief were significantly larger than that with 50micrometer(P<0.0001). 4. SEM micrographs showed favorable marginal reproducibility of zirconia core and smooth texture on the milling surface. CONCLUSION: The marginal discrepancy and the internal gaps of zirconia core were clinically acceptable and the milling surface was showed smooth texture. For fabrication of the durable esthetic restoration, further investigations on complex design of core, milling accuracy, compatability of enamel porcelain and porcelain firing seems to be needed.